CSQ 1020, Werte des Lämpchen des Netzschalters

[Regiefreund]

Liebe Braun-Freunde,

das Lämpchen (Glassockellampe) des Netzschalters meines CSQ 1020 hat sich verabschiedet. RIP.

Auf dem Stecker und auf der Platine ist kein Wert eingetragen. Ich habe leider auch keine Serviceanleitung. Auf dem Lämpchen steht OSRAM und 24... / 30...

Kann mir bitte jemand den nötigen Wert mitteilen, zum Neukauf? (provisorisch habe ich eine viel zu helle Lampe 12W / 5V eingesteckt)

Hätte jemand für mich eine Kopie der Serviceanleitung für den CSQ 1020, das wäre superklasse? Oder eine www.link dazu?

Beste Grüße
Gerhard

[raimund54]

Hallo Gerhard,

schau mal hier: http://www.reichelt.de/T4-T5-T10-Sockel ... 776f075c14

Grüße,

Raimund

[roland]

hallo zusammen,

wenn es das von raimund abgebildetes lämpchen ist...dann kannst das auch von mir haben...hab einige vorrätig

[Regiefreund]

Guten Abend Raimund und Roland,

Danke für die Werte, das ergänzt meinen "Lückentest" von dem partiell abgerubbelten Lämpchen. Ich versuche ein Exemplar bei Conrad direkt zu besorgen. Falls nicht vorrätig, komme ich gerne auf Dein Angebot, Roland, zurück. Danke.

Beste Grüße
Gerhard

[Pavlin]

Hello,

First of all excuse me for writing in english, but my Deutsch is very, very limited.
I'm new here, just acquired a Braun CSQ 1020 preamplifier.
It should be in very good condition, according to sellers words, but unfortunately I couldn't test it yet, because it seams I don't have appropriate cables.
My setup is: Jamo MFB90 speakers (DIN connectors), Dual 601 turntable (DIN output), some tape decks and CD players - both categories have chinch in/out connectors.
I hoped I'd be able to connect at least the Dual TT and the speakers to here the sound, but nothing came out.

I'd be very thankful for any information or link to such helping understand what signals are provided/expected from/to the CSQ 1020 connectors. Surely even better will be to get original interconnects, but searching on the internet I wasn't able to find any.

Kind regards,

Pavlin

[raimund54]

Hi Pavlin,

you should connect your Dual 601 TT to the phono input. The Jamo MFB90 can be connected with a DIN-Kabel 5-pin to the LV-Output vorne (front) of the CSQ 1020. You have to switch on the MFB90 manually with the power switch on the back side of the speakers.

Regards,

Raimund

[Pavlin]

Thanks a lot for the quick help!
I'll try this tonight after work.
Actually I tried that already yesterday, but I'm not sure if I used the front LV output.
Since there was no sound I thought that there may be some specific wiring of the 8 pole LV connector.

Any idea where to get service/user manual for CSQ 1020?

Nice day,

Pavlin

[raimund54]

Hi Pavlin,

the 7-pin LV output do have left channel on pin 3 and right channel on pin 5, ground is pin 2 (and 6).

Don´t forget to press the lv button at the front (right beneath the power switch).

Regards,

Raimund

[Pavlin]

Thanks a lot for the Pinouts of LV connector!

Yesterday I plugged my TT to the phono socket and connected one of my Jamo MFB 90 active boxes to to the LV connector labeled "front". Then switched the Jamo from its connectors pannel. There was laud hum comming out of the box. Nothing like music even in background .
It could be that the Pinouts are different. I'll check that again tonight.

Or may be the preamp is broken (?)

Kind regards,

Pavlin

[Regiefreund]

Hi Pavlin,

sorry I have no manuals to sent to you, but you may look at the pages of FHein in order to buy the manual you want to. The price should be ok.
See http://atelier.tobit.net/ goto manuals and look for CSQ 1020.

Kind regards
Gerhard