Die Suche ergab 25 Treffer

von zbyszek
28.10.2021, 17:04
Forum: Receiver/Verstärker
Thema: CSV 13 Grundüberholung
Antworten: 11
Zugriffe: 7593

Re: CSV 13 Grundüberholung

Hello Klaus, R1B in original circuit with 22K anode and 820 cathode resistors has 28.3dB gain and 16kOhm output impedance. I made a comparison of the two phono sections. The yellow line shows how the passive filter in the circuit complies with the RIAA curve. A function with inverse RIAA filter is a...
von zbyszek
23.10.2021, 20:44
Forum: Receiver/Verstärker
Thema: CSV 13 Grundüberholung
Antworten: 11
Zugriffe: 7593

Re: CSV 13 Grundüberholung

Hi Klaus, Here is how the RIAA stage should look. https://i.postimg.cc/5Xchr2q0/CSV13-RIAA.png Please notice that the R104 1M resistor to ground goes immediately after the 1A tube. Remove the R107. This way, the low frequencies are much better extended. Also of importance is not to change the anode ...
von zbyszek
18.10.2021, 20:12
Forum: Receiver/Verstärker
Thema: CSV 13 Grundüberholung
Antworten: 11
Zugriffe: 7593

Re: CSV 13 Grundüberholung

Hello, I will be writing in English, because it will be easier for you to translate to German than to understand my German. :oops: I have had a CSV13 as my daily driver for about eight years now, and have completely rebuilt my amp. There are at least two approaches to restoring a vintage amp like th...
von zbyszek
05.03.2021, 22:48
Forum: Plattenspieler
Thema: PS 500 plate rubbing
Antworten: 6
Zugriffe: 4085

Re: PS 500 plate rubbing

Hi There are two possible reasons for the issue. 1. If the platter is not parallel to the top plate when the transport screws are put in - the subchasis is skewed 2. If the platter is parallel to the top plate when the transport screws are put in, but is still too close to the top plate and scratche...
von zbyszek
15.04.2020, 10:20
Forum: Plattenspieler
Thema: Tonarmkabel PS 500
Antworten: 4
Zugriffe: 3337

Re: Tonarmkabel PS 500

Die Buchse ist nicht geklebt, da sie zur Einstellung das Azimut um 2 Grad gedreht werden kann.
Eine weitere Demontage ist nicht möglich.

Wickeln Sie einen dünnen Kupferdraht um die Spitze des Lötkolbens, um die Spitze zu verlängern.
von zbyszek
11.04.2020, 12:27
Forum: Plattenspieler
Thema: Tonarmkabel PS 500
Antworten: 4
Zugriffe: 3337

Re: Tonarmkabel PS 500

Die Buchse kann leicht vom Tonarm entfernt werden, wenn Sie die Schraube entfernen.
Das Löten neuer Kabel kann schwierig sein. Sie benötigen einen feinen spitzen Lötkolben.
Das grüne Kabel überbrückt beide Kanalmassen in der Buchse.

Zbyszek
von zbyszek
27.09.2019, 13:28
Forum: Plattenspieler
Thema: How fast should a PS-500 platter get up to speed?
Antworten: 5
Zugriffe: 5291

Re: How fast should a PS-500 platter get up to speed?

I forgot to mention, that the idler string tensioning should be done in the Off position.
von zbyszek
27.09.2019, 12:38
Forum: Plattenspieler
Thema: How fast should a PS-500 platter get up to speed?
Antworten: 5
Zugriffe: 5291

Re: How fast should a PS-500 platter get up to speed?

Hi, I would check if the idler wheel tensioning is okay. The on/off button draws a string that tensions the idler wheel spring. The service manual available in German has useful diagrams. The idler wheel is properly tensioned when there is a 0.5-1.0mm space between the idler wheel and motor pulley, ...
von zbyszek
02.04.2017, 15:59
Forum: Atelier-Reihe
Thema: CD4 - Play button does not always work.
Antworten: 9
Zugriffe: 9031

Re: CD4 - Play button does not always work.

Thank you for your help. I have fixed the issue. :D

The service manual for CD4 gives the same 0.3V value.
Before adjustment, the value was 0.6V.

Also, the measurement has to be done while a CD is playing. When stopped, the value is higher, around 0.45V
von zbyszek
02.04.2017, 11:14
Forum: Atelier-Reihe
Thema: CD4 - Play button does not always work.
Antworten: 9
Zugriffe: 9031

Re: CD4 - Play button does not always work.

Indeed, there is a bulletin listed on the radiodesign.de page. None of the links is working though.

I will be grateful if someone shares the info on the fix for this issue.
von zbyszek
31.03.2017, 20:15
Forum: Atelier-Reihe
Thema: CD4 - Play button does not always work.
Antworten: 9
Zugriffe: 9031

Re: CD4 - Play button does not always work.

Thank you for your answers. The issue is not with the Start button not being pressed strong enough. The player recognises that the Start button was pressed, because it starts spinning the disk. However, it does not start playing the disk, but stops spinning and behaves as if the disc ended (or the R...
von zbyszek
06.03.2017, 11:00
Forum: Atelier-Reihe
Thema: CD4 - Play button does not always work.
Antworten: 9
Zugriffe: 9031

CD4 - Play button does not always work.

Hello, I have an issue with my CD4 player. On some CDs, when I press the Play button, it does not start playing and behaves as if the Return button was pressed (Display shows the "Disc" text only, and the LED above the Return button is shining). When I press the Play button again, it start...
von zbyszek
21.03.2016, 21:07
Forum: Receiver/Verstärker
Thema: CSV 13/60 CCIR -> RIAA conversion
Antworten: 7
Zugriffe: 11538

Re: CSV 13/60 CCIR -> RIAA conversion

Sorry for posting again under my own post. I have come back to the CCIR > RIAA conversion problem, this time with some SPICE computer modelling. After many hours of research and testing, I managed to adjust the equalization curve. This is how the phono stage with RIAA should look. https://farm1.stat...
von zbyszek
07.02.2016, 13:49
Forum: Receiver/Verstärker
Thema: Unterschiede CSV 13
Antworten: 26
Zugriffe: 37638

Re: Unterschiede CSV 13

All versions have sockets for electrostatic speakers. The schematics for the late CSV13 have the power supply for the tuner drawn in a different place, which may be the source of confusion. CSV 130 name is only to be found on the schematics. The name plate has CSV13 written on it. You can find photo...
von zbyszek
07.02.2016, 10:16
Forum: Receiver/Verstärker
Thema: Unterschiede CSV 13
Antworten: 26
Zugriffe: 37638

Re: Unterschiede CSV 13

From my observations: CSV13 early model - Serial numbers up to 6500. Three switches on the right. Volume pot soldered on the preamplifier board. Preamplifier board marked CSV13. CSV13 late model - Serial numbers from 6501 (So called CSV130). Three switches on the right. Preamplifier board from CSV60...
von zbyszek
08.11.2015, 16:38
Forum: Receiver/Verstärker
Thema: CSV 13/60 CCIR -> RIAA conversion
Antworten: 7
Zugriffe: 11538

Re: CSV 13/60 CCIR -> RIAA conversion

I did some research in phono equalisation curves. I don't know why the curve used in CSV13 is called CCIR, because it is clearly the DIN 45537 standard with 50µsec + 318µsec + 3180µsec time constants. RIAA has 75µsec + 318µsec + 3180µsec. When we superimpose the RIAA and Braun's CCIR curve, this is ...
von zbyszek
02.11.2015, 11:58
Forum: Receiver/Verstärker
Thema: CSV 13/60 CCIR -> RIAA conversion
Antworten: 7
Zugriffe: 11538

Re: CSV 13/60 CCIR -> RIAA conversion

Thanks.

I have already received the relevant information from the user Wickerige. I am very grateful for that.

I will post my results when I complete the conversion, so that this topic has any value for the future.
von zbyszek
01.11.2015, 14:28
Forum: Receiver/Verstärker
Thema: CSV 13/60 CCIR -> RIAA conversion
Antworten: 7
Zugriffe: 11538

CSV 13/60 CCIR -> RIAA conversion

Hello, I tried to find information about converting the phono stage equalization curve from CCIR to RIAA. Unfortunately, the article about restoring and modifying a CSV13 amplifier, which had the necessary information, is no longer available at frihu.com Does anyone know which capacitors and resisto...
von zbyszek
30.06.2015, 22:36
Forum: Atelier-Reihe
Thema: CD2/3 Zwei Probleme
Antworten: 0
Zugriffe: 2213

CD2/3 Zwei Probleme

Hallo, Ich habe eine CD2 / 3 gekauft. Der Sound ist gut, aber wenn ich auf "Return" -Taste, oder, wenn die CD endet spielen, gibt es ein Rauschen in den rechten Kanal. Eine kurze, starke Geräusche, ähnlich der erzeugt wird, wenn ein Verstärker mit einer gebrochenen Filterkondensator abgesc...
von zbyszek
18.07.2014, 17:00
Forum: Regie-Reihe
Thema: Regie 501k - schwache Bässe, ton Potis Fehlfunktion
Antworten: 1
Zugriffe: 2728

Ich habe T404 und T504 Transistoren mit Original ersetzt. (Früher gab es einige andere Transistoren installiert ist). Jetzt arbeiten die Klangregler für den linken Kanal, aber nicht für das Recht. Beide Transistoren sind ok. Ebenso ist der rechte Kanal leiser als der linke Kanal. Irgendwelche Vorsch...
von zbyszek
18.07.2014, 10:14
Forum: Regie-Reihe
Thema: Regie 501k - schwache Bässe, ton Potis Fehlfunktion
Antworten: 1
Zugriffe: 2728

Regie 501k - schwache Bässe, ton Potis Fehlfunktion

Hallo, Ich habe ein kleines Problem mit meiner regie 501k. Ich habe alle Elkos im Empfänger ersetzt, und tat allgemeine Wartungsarbeiten. Der Empfänger funktioniert gut, aber es gibt sehr wenig Bass. Auch bemerkte ich, dass der Ton Potis nicht, wie sie sollten. Selbst wenn auf den Maximalwert von +1...
von zbyszek
30.04.2014, 21:50
Forum: Plattenspieler
Thema: PS 500 detail
Antworten: 14
Zugriffe: 13404

I bought two turntables Braun ps-500 and the mechanism detail start-stop is broken in both tuntables.
The original part looks perfectly fine for me. Why do you say it's broken?
von zbyszek
15.03.2014, 19:09
Forum: Regie-Reihe
Thema: Regie 501k - lauten Knall beim Einschalten
Antworten: 2
Zugriffe: 3652

Hallo Heinrich, Vielen Dank für Ihre Antwort. Es sieht aus wie ich muss, um Einschaltknacks gewöhnen. Ich werde prüfen, indem eine Soft-Start-Schaltung mit dem Trafo. Ich beendete Austausch der Elkos in der ganzen Empfänger, und ich bin sehr glücklich mit Klangqualität. Es sieht sehr gut aus mit mei...
von zbyszek
13.03.2014, 16:37
Forum: Regie-Reihe
Thema: Regie 501k - lauten Knall beim Einschalten
Antworten: 2
Zugriffe: 3652

Regie 501k - lauten Knall beim Einschalten

Hallo, Wenn ich den Empfänger einschalte, gibt es einen lauten Knall in den Lautsprechern. Gibt es eine Soft-Start-Schaltung in den Verstärker, die kaputt ist, oder ist es ein normales Verhalten? Ich habe alle Elkos im Endstufe ersetzt, aber es hat nicht das Problem lösen. Wenn ich den Verstärker au...
von zbyszek
28.02.2014, 00:09
Forum: Regie-Reihe
Thema: Regie 501 - Signal strength indicator
Antworten: 0
Zugriffe: 2033

Regie 501 - Signal strength indicator

Hello,

I am sorry for writing in English. Please feel free to answer in German.

I have a small problem with my Regie 501 receiver. The signal strength indicator (to the left from the scale) has stopped working. Can this be repaired in any manner? What may be the reason?